2150 H.D. Carbon Crust Remover & 2151 "T"" H. D. Carbon Crust Remover


		Home \| About ShoreBest \| Cross Reference

New Masonry Cleaners	Rest- oration Cleaners	Paint Strippers	Remedial Products	Water Repellents	Environ-mental Products	Concrete Products	EIFS Appearance System

2150 H.D. Carbon Crust Remover, 2151 "T" H. D. Carbon Crust Remover

Description 2150 H.D. Carbon Crust Remover is for use in the removal of heavy carbon buildup that has accumulated over many years of exposure to industrial and other pollutants. It may be required for cleaning the entire building facade or for removal of carbon buildup that is frequently found under eaves, windowsills and other building projections. 2150 H.D. Carbon Crust Remover can also be helpful in the detailing of water run streaks as a part of the overall building cleaning process especially when cleaning pre-cast or site cast concrete, limestone and concrete block structures.

The most effective use for 2150 H.D. Carbon Crust Remover is as a part of a two-step cleaning process where 2150 is the first application that helps break down the heavy crust that most acid cleaning products cannot effectively remove. The application of 2150 is followed by a neutralization and final cleaning application of 2100 ProStore Restoration Cleaner, 2115 Hi-Clean or 2130 Limestone Neutralizer. Proper use of this system will result in a self-neutralizing cleaning project.

Unlike most competitive systems, 2150 can be applied by low-pressure spray equipment that should result in a lower cost per square foot for labor expense.

2150 "T" H. D. Carbon Crust Remover
2150 "T" H. D. Carbon Crust Remover has all of the same characteristics as the regular 2150 but is thickened for brush or roller application to overhead and other surfaces where a longer dwell time is required.

demonstrates a 2 stage system of first cleaning with 2150 H.D. Carbon Crust remover followed by cleaning with 2115 Heritage Restoration Cleaner

Preparation

Provide protection for foliage, auto and pedestrian traffic, all painted and anodized surfaces. Test all other non-masonry surfaces for possible adverse reactions. Protect all surfaces and surrounding areas from possible damage which might occur from spillage or spray during usage.

All projects should start with a test application to determine the suitability of the cleaner, acceptable application method, dwell time and in some cases dilution ratio. When cleaning heavily soiled surfaces, the cleaner is most often used undiluted. Test areas of at least 10 square feet are recommended and should involve the most severely contaminated area. When possible, the test area should be left to age for 10 or more days to check for possible latent adverse reactions that might require a change in cleaner or cleaning system.

Application

2150 H.D. Carbon Crust Remover may be applied by low-pressure spray or synthetic brush. Dwell times may vary from 15 to 60 minutes. Do not allow the cleaner to dry on the surface. If drying occurs, a light misting of the cleaner will return the cleaner to active status. Remove the cleaner and soiling with high-pressure water rinsing equipment. When using the two-step method of cleaning, apply the properly diluted neutralizer/cleaner to the rinsed area before the surface dries. If the surface has dried, a thorough wetting of the area will be required prior to applying the second step. Do not leave the 2150 cleaned area un-neutralized to sit over night in any case.

Limitations

2150 H.D. Carbon Crust Remover is for use by professional contractors only. Do not use 2150 on black marble or allow contact with any polished masonry surface. Do not allow the cleaner to dry on any surface.

Technical Data

Appearance: Amber Liquid	Solubility: 100%
Biodegradable: Yes	Odor: Mild Soap
Emulsification: Excellent	pH Level: 14 (concentrate)
Flash Point: None	Rinsing: Complete
Stability: Good	Wetting Ability: Excellent
All projects should start with a test application to determine the suitability of the cleaner, acceptable application method, dwell time and in some cases dilution ratio. When cleaning heavily soiled surfaces, the cleaner is most often used undiluted. Test areas of at least 10 square feet are recommended and should involve the most severely contaminated area. When possible, the test area should be left to age for 10 or more days to check for possible latent adverse reactions that might require a change in cleaner or cleaning system.

Safety

All applicators must wear OSHA recommended protective equipment. 2150 H.D. Carbon Crust Remover contains Potassium Hydroxide. Avoid contact with the skin, eyes or clothing. Diluted and undiluted product can cause severe burns. Keep out of the reach of children. Do not ingest or inhale the cleaner, modify the cleaner with any material other than clean water or use the cleaner for any non-recommended purpose. Refer to the proper MSDS Sheet for treatment for persons exposed to or reacting to the cleaner.

Customer Service & Technical Assistance

Factory personnel can be contacted at 800-860-4978 for specific recommendations without any obligation.

Factory trained representatives are available in many locations to assist with project recommendations and dealer locations for purchase of materials. Call 1-412-471-3330 for the name and location of your nearest representative or dealer.